Caliper is curing and oven will be perfect to powder coat I hope. Tomorrow I ll try my first part.
I will try to keep this blog updated with my progress on my new project : a 1967 triumph spitfire mk3. Hoping this will help others and hoping I will get help as I would like to do things right.
Saturday, September 3, 2011
Darling what did you put in our oven !??!!!
Caliper paint
Finally went down the easy route of caliper special paint.
As usual the most annoying part was the cleaning and prep.
Next : Install the new shiny pistons and rebuild kit !
As well I was worried that with powder coating the paint might sneak into places I dont want it to be and I didn't want this caliper to be my first attempt at powder coating
Tuesday, August 30, 2011
Clutch pedal connexion
Same problem with the clutch pedal, the hole is not round anymore ! More welding required yeehah
As well I am wondering if there's supposed to be some sort of recall spring ? There's one on the brake pedal but not on the clutch
Sunday, August 28, 2011
Master cylinder overhaul triumph spitfire mk3
So I finally got the right kit. Actually it is the same for the brake and the clutch master cylinder.
Below is photo of the assembly before replacing the rubbers.
That worked pretty on the first one, on the second I didn't drill straight. Oh well, will need to re-weld and re-drill.I wonder if that will hold and if the pin will wear first.
Next step : Brake calipers. But before replacing the rubbers and the cylinders, I am wondering if I want to powder coat them ?
Monday, August 15, 2011
Brake master cylinder repair
I red as well that Dot 5 doesn't collect moisture so that sounds great too.
From looking inside the brake master cylinder it was well needed. Bad news is I need new brake pistons.
Found it difficult to get the piston out of the brake master cylinder because it really fell like something was holding it inside but no way to get to it. Here is the procedure :
1. Remove the circlip at the end
2. Tap on newspaper to get the piston out or like I did get a bit of compressed air to help. Be careful it can really transform into a projectile.
Once out I realize that none of these rings seem to be the right size. I ordered the "fit most mk3 kit" stupid me, probably due to the fact that I have an early mk3 I have a single line brake circuit so I will need to order a different kit.
I think they must be starting to like me a lot where I order my parts :-)
For now, vacation and will continue when I return.
Saturday, August 13, 2011
Sunday, August 7, 2011
Gearbox oil
While I was at it reinstalled the restored wiper motor and steering wheel and went for a short ride. Engine lacks power at time, better tuning is needed, to be continued. Next big thing on list, brakes ?
Sunday, July 31, 2011
Spitfire restoration steering wheel
Cleaned and painted the wiper motor while I was at it.
Monday, July 25, 2011
SU Carburetors like new
I cleaned them best I could and they look really nice now. Notice on the left the bag of parts that have been replaced, even the needle is new.
I used the following technique to tune, from an article I found on classic car magazine uk. Thanks to them, that got me started and I found it simple to understand.
Friday, July 15, 2011
Sunset on carb parts
To be continued in a few days...
Thursday, July 14, 2011
Monday, June 13, 2011
Tuesday, June 7, 2011
Saturday, June 4, 2011
Sunday, May 22, 2011
We have a runner !
Sometimes it helps, 2 heads scratching at the same time. My dad is here on vacation for a few weeks and gave me a hand. What did we do really ? I had realigned the timing, then new spark plugs, news leads and she ran ! So excited, tried to put back the radiator as fast as possible to go for a drive !
The car drove to the next block and back. Quite fun and the engine seems to be working fine although it does idle really high.
Something strange though, it's difficult to put the car in reverse and first gear, sounds like gears grinding together, I know there's no synchro in these 2 gears so that might normal ?
Saturday, May 14, 2011
Friday, May 6, 2011
Title application
Sunday, May 1, 2011
Rocker cover
At least I managed to take the cam cover off using razor blades.
Not very dirty in there and there some bolts that don't look original, so the engine might have been rebuilt before. Not sure if that's a good or bad news...
Carbs clean
Now still no luck starting grrrr. Plugs seem to receive gas, I have spark and then checked compression in cylinder 4 good. Hum need to think about all this...